{"id":4657,"date":"2026-08-11T18:03:50","date_gmt":"2026-08-11T18:03:50","guid":{"rendered":"https:\/\/etisystems.com\/what-is-actuator-in-an-embedded-system\/"},"modified":"2026-08-11T18:03:50","modified_gmt":"2026-08-11T18:03:50","slug":"what-is-actuator-in-an-embedded-system","status":"publish","type":"post","link":"https:\/\/etisystems.com\/en-gb\/what-is-actuator-in-an-embedded-system\/","title":{"rendered":"What Is an Actuator in an Embedded System?"},"content":{"rendered":"\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

An actuator<\/strong><\/a> takes an electrical signal from a microcontroller and turns it into real movement, force, or pressure. The processor decides what needs to happen. The actuator<\/strong> is what actually makes it happen. Without one, a control loop can sense the world, but it can never act on it.<\/p>

How an Actuator Converts Electrical Signals Into Physical Motion<\/h2>

A microcontroller can’t move anything on its own, so it starts by sending a signal, usually a PWM pulse or a set voltage, to a driver circuit. That driver boosts the signal to a level the actuator<\/strong> can actually run on. Most microcontroller pins only output 3.3V or 5V, and that’s nowhere near enough current to run a motor, solenoid, or valve. Once the driver supplies the right voltage and current, the actuator takes over and turns that electrical energy into motion, whether that’s a rotation, a linear push, or a straight mechanical force.<\/p>

Where Microcontrollers Fit Into Actuator Control Loops<\/h2>

Embedded systems rarely run an actuator open loop for long. A typical control loop starts with a sensor reading a physical condition, such as position, pressure, or temperature. The microcontroller checks that reading against the target value it’s trying to hit, works out how far off it is, and adjusts the signal going to the actuator to close that gap. This closed-loop structure, often built around a PID algorithm, lets the system correct its own output continuously instead of applying a fixed command and hoping the result lands where it should. Industrial designers rely on this structure heavily in valve positioning, robotic joint control, and motion platforms where accuracy has to hold under variable loads.<\/p>

Electric, Pneumatic, and Hydraulic Actuators: How Embedded Systems Choose<\/h2>

Embedded applications call for different actuator types depending on the force required, the speed needed, and the environment in which the system operates.<\/p>

Electric Actuators<\/h3>

Motors, solenoids, and piezoelectric elements all fall under this category, and they run directly off electrical current. That’s what makes them so easy to pair with microcontrollers, PLCs, and IIoT platforms \u2014 the signal and the power both stay electrical, with nothing else to translate. There’s also less upkeep involved. No fluid lines, no seals, no compressors to service. A lot of current models come with position feedback already built in, ready for closed-loop control out of the box.<\/p>

Pneumatic Actuators<\/h3>

These run on compressed air, which gives them high speed and force in a small footprint. The catch is control: an embedded system can’t just send voltage to a pneumatic actuator the way it would with an electric one. It has to go through a proportional directional valve instead, since the actuator itself only responds to air pressure. They’re strong performers for fast, point-to-point moves, but air behaves in nonlinear ways, and a control algorithm has to be tuned to handle that.<\/p>

Hydraulic Actuators<\/h3>

Hydraulic actuators move heavy loads with the level of precision fluid power is known for, using pressurized oil rather than air. Oil barely compresses, so force applied at one end of the system reaches the other end almost instantly and evenly. That’s why hydraulic actuators still dominate heavy machinery and high-torque valve applications. On the control side, embedded systems send a current or voltage signal to a proportional valve, and the valve regulates fluid flow to the actuator from there.<\/p>

How Position Feedback Sensors Keep Actuator Movement Accurate<\/h2>

If an actuator moves without reporting back, the controller has no way of knowing where the load actually landed. Potentiometers and encoders solve that problem. They track the actuator’s physical position and turn it into an electrical signal that the microcontroller can read. Take valve control as an example: a potentiometer mounted on the actuator shaft reports its exact position back to the controller. The controller checks that the reading against the setpoint it’s targeting, and if the two don’t match, it sends a correction signal to close the gap.<\/p>

Common Actuator Applications in Industrial Embedded Design<\/h2>

Actuators show up across a wide range of industrial equipment, and the control approach shifts depending on the job. Proportional valve actuators regulate fluid and gas flow in process control systems. On heavy equipment, joysticks use potentiometers and Hall-effect sensors to read operator input and convert it into proportional actuator commands. Robotic arms take it further, running several coordinated actuators at once, each with its own feedback loop, to keep a tool positioned accurately no matter how the load shifts.<\/p>

Automotive suspension systems use compact electric actuators to adjust ride height and damping in real time, a use case covered in more depth in What Are Commonly Used as Actuators in Electronic Suspension Systems?<\/strong><\/a><\/p>

Selecting the Right Actuator for a Given Embedded Application<\/h2>

Choosing an actuator starts with the load: how much force or torque the application needs, how fast the actuator has to respond, and how precisely it needs to hold position under that load. Environmental conditions matter next, since temperature extremes, moisture exposure, and vibration all narrow the field of viable actuator types. Duty cycle plays a role too, since a component running continuously wears differently than one cycling occasionally. Design teams sourcing components for a build often cross-reference specifications through industrial distributors such as DigiKey<\/strong><\/a> before finalizing a part number.<\/p>

For a full breakdown of actuator categories, specifications, and selection criteria, see What Is an Actuator? A Comprehensive Guide for Industrial Applications<\/strong><\/a>.<\/p>

Frequently Asked Questions<\/h2>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t
\n\t\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t\t\t\tWhat is an actuator in a microcontroller-based system?<\/a>\n\t\t\t\t\t<\/div>\n\t\t\t\t\t

It is the output device a microcontroller drives, through a driver circuit, to convert an electrical control signal into physical motion or force.<\/p><\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t\t\t

\n\t\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t\t\t\tWhat are the main types of actuators used in embedded systems?<\/a>\n\t\t\t\t\t<\/div>\n\t\t\t\t\t

Electric, pneumatic, and hydraulic actuators cover most embedded applications, and each one fits a different combination of force, speed, and operating environment.<\/p><\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t\t\t

\n\t\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t\t\t\tWhat is the difference between an actuator and a sensor?<\/a>\n\t\t\t\t\t<\/div>\n\t\t\t\t\t

A sensor reads what’s happening in the physical world and turns it into an electrical signal. An actuator works the other way around, taking an electrical signal and turning it into physical action.<\/p><\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t\t\t

\n\t\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t\t\t\tWhy do actuators need feedback sensors?<\/a>\n\t\t\t\t\t<\/div>\n\t\t\t\t\t

A controller can’t confirm an actuator reached the right position without something reporting back. Potentiometers and similar feedback sensors send that position data back, so the system can correct for load changes as they happen.<\/p><\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t\t\t

\n\t\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t<\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t\t\t\tCan a microcontroller drive an actuator directly?<\/a>\n\t\t\t\t\t<\/div>\n\t\t\t\t\t

Only in low-power cases. Most actuators draw more current than a microcontroller pin can supply, so a driver circuit sits in between to handle the load.<\/p><\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t